Deutsch English

Module 9040 Line symbol just with tilting counter (changeover switch)

Module 9040 Line symbol just with tilting counter (changeover switch)
Zoom image

7,25 EUR

19 % VAT incl. excl. Shipping costs

Shipping time: 3-4 Days

Product no.: 9040
Module 9040 Line symbol just with tilting counter (changeover switch)

Module 9040

Line symbol just with tilting counter (changeover switch) to the turning on and switch offed of the driving stream in the rail segments which are not covered by signals

 

 

Customers who bought this product also bought the following products:

Module 9012 Line symbol 45 parallel

Module 9012 Line symbol 45 parallel

Module 9012

Line symbol 45° parallel

 

 

1,35 EUR (19 % VAT incl. excl. Shipping costs)
Drive Controller 2030 for two-wire DC tracks, analogue

Drive Controller 2030 for two-wire DC tracks, analogue

Drive Controller 2030 for two-wire DC tracks, analogue

This electronic drive controller was specially developed for use in track control panels and is suitable for all two-wire DC track systems. With the appropriate power supply from a suitable AC transformer of approximately 16-20V and at least 25VA, a maximum current of ca. 1,2A can be drawn.
Operation is very simple. The potentiometer delivered with the module is the only operating control. The neutral position of the drive controller is equivalent to the potentiometer’s middle setting. By twisting the control button to the left or right, the traction vehicle is driven in the respective direction. This occurs with pulse width-controlled traction current, as a result of which unimaginable, delicate manoeuvres are possible, especially in the go slow area! By means of a setting controller attached to the front side of the electronic component, start/ brake delays can be set, in order to achieve a mass simulation of the train being controlled. This can, of course, also be set to neutral – that is, without delay.
The LEDs delivered with the module display the respective direction of travel. Only in neutral position (control button in middle position) are both off. In the event that the integrated electronic overload protection is activated, the traction current is switched off and both LEDs flash. Only once the cause of the overload has been eliminated and the controller has been set to neutral does the flashing cease and the traction current is switched on again.
The set contains all components required for assembly with the track control panel. The potentiometer is suitable for assembly with a blank module from the Digimoba signal box system. When assembling the module with other track control panels, please note the maximum thickness of the supporting material of 4mm!

55,70 EUR (19 % VAT incl. excl. Shipping costs)
Signal Module 2041 for main and approach light signal

Signal Module 2041 for main and approach light signal

Signal Module 2041 for main and approach light signal

This signal module is a further development of 2040. The decisive difference is its capacity to be used for light signals for differently polarised terminals. While only signals with a mutual positive connection could be used as return conductors in 2041’s precursor 2040, this no longer plays a role, thanks to the alternating current technology in 2041. Both positive and negative poles of the power supply can be used as mutual return conductors. Another advantage can be found in the wiring for the approach signal due to the elimination of additional diodes for decoupling. The respective approach signal (with up to three signal aspects) is directly connected to the signal module 2041! The polarity of the mutual return conductor also plays no part here!
The purpose of the signal module is to control a light signal with up to 4 aspects, by which an approach signal attached to the same tower as the main signal is prototypically dimmed when a main signal of ‘stop’ is shown. Electronics controlled by a microprocessor ensure realistic panning of the signal aspects. Via an in-built relay contact, the traction current or other form of control current can be controlled potential-free. And for travel in the opposite direction at a red signal, an individual gate is available. Activation occurs via a short ground impulse at the desired input. Built-in LEDs are for supervision purposes and always show the current signal aspect.

 

43,30 EUR (19 % VAT incl. excl. Shipping costs)
Module 9031 Signal module for right-hand traffic. Yellow / Red - signal picture

Module 9031 Signal module for right-hand traffic. Yellow / Red - signal picture

Module 9031

Signal module for right-hand traffic. Yellow / Red - signal picture

 

12,00 EUR (19 % VAT incl. excl. Shipping costs)
Module 9032 Signal module for right-hand traffic. Green / Red / Yellow signal picture

Module 9032 Signal module for right-hand traffic. Green / Red / Yellow signal picture

Module 9032

Signal module for right-hand traffic. Green / Red / Yellow signal picture

 

16,20 EUR (19 % VAT incl. excl. Shipping costs)
Module 9021 Rail occupied illumination module with red Luminous diode for line ahead

Module 9021 Rail occupied illumination module with red Luminous diode for line ahead

Module 9021

Rail occupied illumination module with red Luminous diode for line ahead

 

 
 
 
 
 
 
 
 
 

5,20 EUR (19 % VAT incl. excl. Shipping costs)

This Product was added to our catalogue on Wednesday 04 March, 2015.

[<<First] | [<Back] | [Overview] | [Next>] | [last>>] | Product 26 of 50 in this category

Shopping cart

You do not have any products in your shopping cart yet.

Welcome back!

E-mail address:
Password:
Forgot your password?

Newsletter subscription

E-mail address:

Customer group


Customer group: Guest

Manufacturer information

Digimoba Elektronic
Digimoba Elektronic
More products

Manufacturer

Parse Time: 0.118s