Deutsch English

Drive Controller 2032 DC, analogue

Drive Controller 2032 DC, analogue

Zoom Zoom image

98,50 EUR

19 % VAT incl. excl. Shipping costs

Shipping time: 3 Weeks

Product no.: 2032
Manufacturer part number: 2032
Manufacturer: Digimoba Elektronic
More products of: Digimoba Elektronic

Print datasheet

Drive Controller 2032 DC, analogue

This novel drive controller differs from its predecessor 2030 primarily due to its switchable pulse width frequency and its increased efficiency, which both makes the use of bell-type armature motors uncritical and also enables use in small outdoor model railways.

It is operated by an incremental encoder, which also has a key function. Up to 63 speeds can be set, shown on the two-digit display. All functions are intuitive and incredibly easy to operate. The direction of travel can only be changed when the vehicle is stationary, as is the case with frequency shifts. The direction of travel is also shown by additional LEDs to the left and right of the display. Furthermore, this controller has an additional immediate and emergency stop function. The default electronic fuse setting is 2,5A.

The drive controller consists of two modules – the electronic module, which can be assembled at any chosen position, and the operating module, which is intended for assembly with a signal box, manual operation box or similar. The size of the controls is matched to the modular dimensions of the Digimoba signal box (2x3 fields), so that assembly can be carried out without issue. The components are connected by a cable, which is delivered with the module.

For larger outdoor model railways, the module is also available as 2033 with up to 8A (!!)

 

Customers who bought this product also bought the following products:

Universal Decoder 1131

Universal Decoder 1131


Universal Decoder 1131

The Universal Decoder 1131 is freely programmable in terms of both its receiving address and its outlet switch time, and a special programming mode is incorporated in control centres with software version V2.12. and above for this purpose. The outlet switch times can be selected from 10 speeds from 0.2 seconds right through to continuous operation. Continuous operation is intended for use with the direct connection of light signals, thus four of the eight outlets are always active in this operating mode. The eight outlets are assigned to four pairs of address outlets. In continuous operation, the odd outlets are active (always the left-hand connector when connectors are lying upwards) in the home position (that is, after switching on the power supply) = stop (red).
For direct connections of motor-operated point mechanisms, switch times of 0.2 to 15 seconds can be programmed for the changeover time, thus eliminating the need for additional relay modules and their extra wiring.
For motor-operated point mechanisms we offer the type 1131 specialized for this using

 

The Switch-to-Ground Prinzip is to make it possible to use external power with higher voltage (up to 24V DC) for more powerfull switching and saving power from the trackswitch voltage source.

39,30 EUR (19 % VAT incl. excl. Shipping costs)
Feedback Module 1151 without case

Feedback Module 1151 without case


Feedback Module 1151 without case

Specifically developed in accordance with modern model railway system requirements. Each feedback module has 8 isolated inlets, electrically separated from the electronic system by optocouplers. The feedback module is connected to the centre 1000 or 1100 using a separate 6-pin cable with modular plugs (8015-19). The feedback modules are simply connected in a row and so can be expanded to up to 32 modules. Thus, up to 256 feedback signals can be fed in. This includes in particular line occupied signals, track switches, track contacts, point position feedback signals, timers, switch keys and other switching operations. Switch keys can also be connected within the signal box for some specific applications (e.g. for track splitting, for operating special edition models and working models, etc.), in order to activate defined processes and automatic mechanisms. These are specified in advance in the central unit ‘Trackswitch’.

31,20 EUR (19 % VAT incl. excl. Shipping costs)
Track Module 2024 for two-wire DC, analogue, specifically for block operation

Track Module 2024 for two-wire DC, analogue, specifically for block operation


Track Module 2024 for two-wire DC, analogue, specifically for block operation

Anyone who has built electronic modules for controlling starting and braking into their system before is familiar with a particular problem – while one train reaches its precise stopping point, a second stops hugely short of it and a third even continues at such a speed that it overshoots the mark entirely or halts abruptly! Regardless of what control attempts are made, nothing is 100% suitable for all vehicles! This is the result of the varying driving characteristics of each of the individual traction units. Therefore, we have developed a track module with speed-regulated delay. By measuring the approaching train, the slow speed during deceleration is set. In this way, faster trains are decelerated more, whereas slower trains are decelerated to a lesser extent, thus allowing each train to arrive at its intended target.

This microprocessor-controlled module functions using pulse width control. 64 speeds are available. It is specifically for use in block sections and is controlled by the input for occupancy indication for the next track section or ground potential (=free) in connection with the three built-in track occupied indicators.

For use in block sections, single- and double-track, without influence in opposite direction. Aside from the occupancy indicator outlets for all three individual sections, there is also an overall occupancy indicator outlet for switching multiple track component 2024s in a row in automatic block section operation or for feedback via feedback modules 1051 and 1151. In addition to this, a light block signal can also be attached. As such, this compact device enables complete and independent block control. One 2024 module is required per block section.

Transit in the opposite direction at a red signal is possible and occurs without influencing the train.

Requires a traction current source (max. 12V=) and an adjunct current supply (16V~ or =) to operate.

Also available without casing at a lower price as 2124.

 

52,60 EUR (19 % VAT incl. excl. Shipping costs)
Track Occupancy Indicator 2102 without case

Track Occupancy Indicator 2102 without case


Track Occupancy Indicator 2102 without case

This fourfold track occupancy indicator works via the current sensor principle and can be used for all types of current and control system, including digital DCC, Motorola, MFX, Selectrix etc. The function and occupancy status of the four track sections that can be monitored can be immediately monitored using the four integrated LEDs. All current consumers with a resistance of up to 15 kΩ can be safely detected.
Digimoba signal box displays, our feedback modules 1051 and 1151 or LEDs with series resistors can be connected to the ports for external displays. Each of the four track occupied indicator outlets is capable of delivering up to 2A of switching current, thus making it suitable for use as a track switcher for direct switching.

35,60 EUR (19 % VAT incl. excl. Shipping costs)
Module 9009 Empty field

Module 9009 Empty field


Module 9009

Empty field

 

 
 
1,05 EUR (19 % VAT incl. excl. Shipping costs)
Module 9010 Line ahead

Module 9010 Line ahead


Module 9010

Line ahead

 

 
1,55 EUR (19 % VAT incl. excl. Shipping costs)

This Product was added to our catalogue on 01/03/2015.

[<<First] |  [<Back] |  [Overview] |  [Next>] |  [last>>] |  Product 10 of 17 in this category

Shopping cart

You do not have any products in your shopping cart yet.

Welcome back!

Newsletter subscription

E-mail address:

The newsletter can be canceled here or in your Account at any time.

Customer group


Customer group: Guest

Shipping country

Manufacturer information

Digimoba Elektronic
More products

Manufacturer